Detailed explanation of the assembly steps of the multifunctional nursing bed
Release time:
2021-09-09
Install the legs of the bed: the two longer ones are the legs of the bed. First, remove the screws on the legs of the bed, clip the legs of the bed to the bed board, and then re-fix the screws. The nuts used in this product are all lock nuts, so you don't need to tighten them too tightly. The two shorter beams are beams, which are respectively fixed on the installed leg of the bed, and gently shake the leg of the bed to ensure that there is no looseness.
1. Install the legs of the bed: the two longer ones are the legs of the bed. First, remove the screws on the legs of the bed, clip the legs of the bed to the bed board, and then re-fix the screws. The nuts used in this product are all lock nuts, so you don't need to tighten them too tightly. The two shorter beams are beams, which are respectively fixed on the installed leg of the bed, and gently shake the leg of the bed to ensure that there is no looseness.
2. Install the casters: The casters of this product are connected by thread. The four casters can be installed in the four screw holes regardless of their positions.
3. Installation of the toilet hole: The toilet hole is composed of three parts: the bed surface toilet hole structure, the bedpan holder, and the toilet hole handle. The bedpan holder is connected with the bed surface by a rod transfer device, and the toilet hole is opened and closed by controlling the spherical handle.
4. Install the head and foot of the bed: the headboard is higher and the footboard is shorter, so the hanging installation method is adopted. Align the bed head hook with the iron pin of the bed iron and buckle the lock.
5. Install the guardrail: align the hole of the guardrail frame with the punched position of the bedside, and fix it with screws, with the guardrail switch facing the side of the bed.
6. Debug the controller: The motor and push rod have been installed before leaving the factory. After the power is turned on, debug through the controller. For details, see "Product Function Introduction".
7. Lay out the mattress; if the product is equipped with a special mattress, follow the design of the bed surface and correspond to the position of the back frame, foot frame and toilet hole.
The installation steps are as follows: ①First, connect the toilet hole with the bedpan holder with the product's built-in anti-loosening screw; ②Secondly, install the spherical handle; ③Next, install the spring buffer device, and fix the handle with the bed leg; ④Then, plug it in Split pin, connect the knob with the passing rod. ⑤Finally, with the bed facing up, move the handle left and right to observe whether the toilet hole is fully opened and reset. Note: If the toilet hole cannot be closed in place, please pull out the split pin, rotate the toilet hole transfer rod, and readjust the position of the toilet hole.
Previous page
Latest News
Talking about the preventive and health-care functions of the multifunctional nursing bed
Prevention of bedsores is caused by the patient's long-term bed rest, which causes local pressure to cause blood circulation obstacles or local malnutrition in this part, followed by local skin and soft tissue ulceration. Bed sores mainly occur in bony areas, such as the middle of the buttocks, the large trochanter area of the upper femur, the back of the heel, etc.; the functions of Fuljia brand multifunctional electric bed, such as raising the back, raising the legs, and turning over, greatly promote the blood of bedridden patients. Circulation to prevent the occurrence of bedsores.
09
2021
/
09
Rehabilitation equipment needs to be used reasonably
Stimulate muscle movement through the correct pattern to achieve the purpose of stimulating nerves.Exercise stretches and compresses the muscles, increases the meridian return pressure, and improves blood circulation.
08
2021
/
09
The basic function of weight loss training with rehabilitation equipment
Walking center of rehabilitation equipment. Walking is a "simple" activity. Under normal circumstances, walking does not require the involvement of the cerebral cortex. Some animals can still crawl after the brain is removed, suggesting that there is a crawling or "walking" center in the spinal cord. However, human walking is closely related to the function of the cerebral cortex. In complex situations and special tasks, the cerebral cortex directly participates in the control of walking posture. Fukuyama and others.
08
2021
/
09
On November 3, 2018, the "2018 China Medical Device Innovation and Entrepreneurship Conference" was grandly held at the Conference Center of the National Independent Innovation Demonstration Zone in Zhongguancun, Beijing. More than 300 medical colleagues from scientific research, clinical, corporate, and investment circles attended the conference.
18
2021
/
08